Orion V2 LED Angel Eyes (168 LEDS) for Nissan GT-R R35

$189.99
In stock
SKU
ae-v2NisGTR
Orion V2 LED Angel Eyes (168 LEDS) for Nissan GT-R R35 is available to buy in increments of 1
Orion V2 LED Angel Eyes (168 LEDS) for Nissan GT-R R35

Title:

Nissan Maxima Orion V2 LED Angel Eyes for R35 GTR -

 

Synopsis:

 

Brightest Output of any product on the market

This product incorporates the brightest Light Emitting Diode technology currently available today. The LED is used in a variety of applications due to it's longevity, durability, and cold weather instant operability characteristics. The Orion Angel Eyes, the only product with the reflective backing to prevent bleeding of the light in all directions points the light output in the direction of the only place that matters - out.

Orion V2TM is daytime visible, mounted inside a high polish crystal light enhancing cover that is the same size as the OEM angel eyes, just brighter. The high quality wiring harness included was the first to be fully insulated and provides you with both a fused primary trigger and a secondary trigger for automatic dimming (fade/on & fade/off) functionality.

High Output 10000mcd LEDs. First of their kind on the market.

 

Surface Mount LED with over 175 degree output.

Application (Please consult your owner's manual for your application fitment type):

ALL 2009-2014 NISSAN GTR (GT-R) R35 Headlights

 

Product Description:

 

  • 4 Orion V2 LED Angel Eye Rings

  • Lifetime Warranty

  • Online Instructions

  • All Hardware and Installation Included

  • Eyelids or Headlights not included

 

Engineering Detail:

 

  • Requires baking of the headlights (20 minutes @ 200 degrees on cookie sheet and bake)

  • 30-50 minute complete install using standard hand tools per side.

  • 36000mcd or 2X as bright as the nearest competitor.

  • Look here for details

 

Benefits:

 

  • Updated Look

  • Allows you to clear or black out your turn signal at the same time

  • Can be wired as DRL (daytime running lights)

    Significant improvement in visual appeal of car

 

1) Remove bolt from fender liner in the wheel well.
2) Remove bolt holding bumper edge just inside peeled back fender liner.
3) Remove all the bolts at the bottom of the bumper
4) Remove 5 pins from the top of the bumper
5) remove bumper.
6) Remove fender bolts holding lights
7) Remove top 2 bolts holding lights
8) Disconnect as many connections as possible prior to...
9) Pulling light out
10) Cookie sheet for 20 minutes at 200 degrees
11) Remove 4 screws holding back of light against front of light plexiglass, gently slide plastic tabs off the front plexiglass while doing this.

12) Remove inner beauty trim's 2 screws.

13) Place rings at respect corners - 1 dap of glue - less than an teardrop worth at the corners of the rings and the bottom of the ring center.
14) Insert ring bottom FIRST, then push gently tops of rings onto beveled edge of trim piece.
15) Hold for 2-3 minutes (use QUICKGRIP for best results)
16) Wait 10 minutes for glue to fully set.
17) Push wires out the back of high beam and low beams respectively, remove the rubber caps frist, then seal rubber caps OVER the wires.
18) Put back into oven for 5 minutes, seal up headlight and re-insert all screws.
19) Attach black connectors.
20) Finish Install by reattaching all body parts.

21) YOU ARE DONE SEE LINK BELOW FOR ADDITIONAL PICS

 

https://www.youtube.com/watch?v=vL78etDylSk

 

 

Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account